RA6402

40QT Orbit Winch™ with QuickTrim™

Lightweight aluminium winch with QuickTrim™ self-tailer, 2 speeds, and Power Ribs™ for controlled grip on the line at all times.

FEATURES

Sprung self-tailing jaws to accept 7 - 12mm line.

QuickTrim™ patented self-tailing feature for rapid sail trim and smooth adjustment.

Ball bearings carry the thrust loads, roller bearings carry the radial loads of the drum to minimise rotational friction.

Proven Andersen winch gearing configuration.

Power Rib™ ensures a controlled grip on the line at all times, whether trimming or easing. Minimal rope wear compared to more abrasive drum surface finishes.

No tools required for configuration and servicing.

Machined aluminium drum – stronger and lighter than traditional cast aluminium drums.

Aluminium centre stem, lighter weight compared to bronze stems.

Low line entry due to gearing configuration geometry.

DAME Category Award Winner

Specifications

Product Specifications
Max. Rope diameter (mm)12
Main Sheet Monohull Boat Size (m)12.2-13.1
Weight (kg)3.1
Performance LevelPerformance Racing, Offshore Racing/Bluewater Cruising, Club Racing/General Cruising
Gear ratio 1st speed1.4:1
Gear ratio 2nd speed6.8:1
Power ratio 1st speed8.3:1
Power ratio 2nd speed40:01:00

INTRODUCING QUICKTRIM™

The innovative QuickTrim™ self tailer allows sailors to easily and safely ease line tension to make minor sail trim adjustments without having to remove the winch handle or take the line out of the self-tailer. Racing sailors can react and respond instantly to minor changes in wind direction or steering, providing an unmatched advantage when frequent sail trim adjustments are required. It’s also a nice convenience for cruising sailors.

On the water, using QuickTrim™ is intuitive and quickly becomes second nature. With one hand on the tail of the sheet, rotating the top cover of the winch anti-clockwise against spring pressure allows the self tailer to turn beneath it like a sheave as the rope is eased out, with smooth grip and control assured by the drum surface and Power Ribs™. When the top cover is allowed to spring back, the self-tailer locks again and grips the line to resume normal use. This simple, reliable feature is a real advantage when making frequent minor  adjustments to sheet and halyard tension.

As delivered from the factory, the Orbit 40QT operates as a traditional two-speed self-tailing winch. The QuickTrim™ feature is enabled by the user, simply by removing a single screw located within the self tailer. Step-by-step instructions are included in the Quick Reference Guide provided with the winch, and in the product manual available from the Support section of the website.

NO TOOLS REQUIRED

Full disassembly and reassembly can conveniently be performed without the need for any tools. To remove the drum, pull back the spring-loaded release latch and a slight anti-clockwise rotation will allow the self-tailing arm to be lifted from the winch. From there, the drum can be removed from the winch centre stem. When completing reassembly in reverse order, an audible click confirms positive engagement between the self-tailing arm and bayonet notches on the centre stem. These notches allow the self-tailing arm to
be locked in one of 8 positions at rotational increments of 45 degrees.

 

POWER RIBS™

Inspired by the distinctive drum profile of Andersen winches, Power Ribs™ have been incorporated into the fully machined drums of Ronstan’s Orbit Winches™ to deliver the same impressive line handling with maximum grip and minimal rope wear. The exceptional grip provided by the Power Ribs™ offers a multitude of benefits: requiring fewer wraps around the drum, reducing the load held in the self tailer, and encouraging the line to slide easily upward on the drum to avoid riding turns. The nonabrasive drum surface extends the service life of running rigging and allows for smooth and controlled easing, even under high loads.

Technical Information

Specification Details

Specification Details
Base "B" Ø (mm)151
Drum "D" Ø (mm)86
Height "H" (mm)166
Line Entry "L" (mm)57

Applications

  • Genoa Sheets
  • Spinnaker Sheets
  • Main Sheets
  • Genoa Halyards
  • Spinnaker Halyards
  • Main Halyards
  • Reef Lines

 

Materials

  • Hard anodised aluminium drum and centre stem, aluminium self-tailing arm.
  • Grade 316 stainless steel shaft and pawls.
  • Grade 2205 stainless steel axle pins.
  • Aluminium bronze gears.
  • Glass-filled nylon self tailer.
  • Self-lubricating acetal ball and roller bearings.

 

Resource Files

pdf
pdf
pdf
dwg
zip

Need some advice?

Send us a
Message

Find a
Distributor