82-3ST Winch FS Electric 24V

82-3 ST Full Stainless Winch, Three Speed Electric, 24 Volt


Intelligent push-button technology.

Easy assembly and dismantling for service and maintenance.

Motor protected from overload by amperage sensor.

All electric motors fitted with thermal cutouts in case of overheating.

Supplied complete with installation manual, electronics box, switches and cable terminals


Product Specifications
M.W.L. (kg)6000
Weight (kg)54
Gear ratio 1st speed3.7 : 1
Gear ratio 2nd speed8.8 : 1
Gear ratio 3rd speed27.7 : 1
Power ratio 1st speed11.0 : 1
Power ratio 2nd speed26.0 : 1
Power ratio 3rd speed81.6 : 1
Manual Speeds3
Electric Speeds3
Max Pull (kg)4000
Notes:Extensions available to suit longer “K” dimensions.


Two and Three Speed Electric Winches

Andersen Two and Three Speed electric winches are the perfect solution for larger boats, of 16m (60ft) or more, providing the power and control to safely hoist and trim sails of any size at the push of a button. In addition to the host of standard features that have made Andersen self tailing winches the benchmark for quality and performance, Andersen Two and Three Speed Electric Winches are engineered with unsurpassed levels of functionality, monitoring and protection.

Efficient, high quality motor
At the heart of each Andersen Two and Three Speed electric winch is a powerful European engineered and manufactured series wound motor. Carefully matched with the optimum gearbox these winches deliver high speed at low load for fast sheeting in, and low speed at high load for safe, fine tuning when trimming. For maximum performance and efficiency they are supplied in a 24 volt version, providing smooth operation across a wide working load range.

Illuminated "intelligent" Push Button
Two and Three Speed electric winches are supplied with push buttons with integrated LED which illuminates when power to the winch system is on. The push button incorporates a hinged safety cover to prevent inadvertent winch operation and is water resistant rated to IP67. The push button also acts with the controller to flash status codes that assist with trouble shooting in the event of overload or where other system protection intervention occurs. A cable for connection of the push button is included for convenient installation.

Unrivalled level of monitoring and protection

  • Integrated Overload Protection The controller is pre-set to stop the winch if the Maximum Pull Load is exceeded. Operation can resume within a few seconds when the load returns below the limit.
  • Thermal Overload Protection – The motor is fitted with a thermal cutout that disables the motor in case of overheating; it automatically resets after the temperature returns to normal.
  • Reverse Polarity Protection – An integrated 5 Amp fuse protects the controller against incorrect cable connection.
  • Accidental Start Protection – Winch operation is disabled if the push button is already inadvertently pressed when the power supply is turned on at the circuit breaker or battery.
  • Low Voltage Detection – Operation is disabled if the battery charge level is low, which prevents further drain on batteries and avoids triggering low-voltage reset of navigation instruments and other electronic devices.
  • Continuous Run Time Limit – Operation is disabled if continuous run time exceeds 10 minutes.

Manual operation

Manual operation is always available as a backup; or just for the experience.

Andersen Two and Three Speed Electric Winches are supplied complete with push buttons, electrics/control box and comprehensive installation and operation instructions.

E2 conversion kits are also available for the 68ST and 72ST (for two electric speeds) and the 82-3ST (for three electric speeds), contact us or your local Andersen distributor for details.

The RA590150 150A Amp Circuit Breaker is recommended for use with 82-3ST – sold separately.


  1. Drive shaft in AISI 329 stainless steel
  2. Self-tailing arm in 316 stainless steel adjustable through 360 degrees (from size 40ST and up)
  3. Low friction curved self-tailing arm
  4. Stainless-steel ball bearings to carry vertical and horizontal loads from the drum (from size 52ST and up). The upper and lower bearings are designed to be maximum distance apart, resulting in increased support for the drum while increasing efficiency
  5. Large-diameter roller bearings to absorb drum loads and increase efficiency
  6. Easy servicing of gears. Captive pawls made from cold-pressed stainless-steel bar AISI 316L, are unbreakable
  7. Upper base plate from aluminium bronze, which is twice as strong as standard bronze and ensures a light, stiff and rugged construction that increases efficiency
  8. The self-tailing system adjusts automatically to suit various rope sizes. Jaws in 316 stainless steel
  9. Lightweight grade 316 stainless-steel drum with Power Rib ensures a superior grip on the sheet without causing excessive wear
  10. Drum surface with Power Rib generates horizontal friction, and a highly polished surface minimizes vertical friction, allowing rope to slide easily up the drum
  11. Lightweight stainless-steel drum combined with an internal construction of aluminium bronze, results in ANDERSEN Winches being of similar weight to aluminium winchesbut far more durable. Servicing is only required every 2 years under normal use.

The Power Rib™

Andersen winch drums incorporate the distinctive Power Rib™ which ensures a controlled grip on the line at all times, whether trimming or easing. The highly polished stainless steel surface minimises vertical friction and allows the loaded rope turns to slide easily upward as the drum rotates, without the shuddering and excessive rope wear seen on winches that rely on a rough surface finish for grip.

Stainless steel roller bearings and ball bearings carry the highest drum loads to the centre stem of the winch, minimising efficiency losses due to friction.

The self tailing arm can be rotated through 360 degrees for optimum positioning (40ST and larger). Stainless steel self tailing jaws adjust automatically to suit various rope sizes.
Andersen winches are designed for simple, straightforward installation and maintenance. Servicing is only required every two years or so under normal use.

It’s all about protecting your investment. With ANDERSEN Winches, this protection is guaranteed, as the drum maintains its grip year after year. Keeping wear and tear to a minimum also helps maintain resale value, and our 3-year warranty and instant service in more than 30 countries worldwide amount to a benchmark standard. Low maintenance is a key — and with ANDERSEN Winches, you can take it for granted. Our winches require less maintenance, since all pawls and springs are captive, and the design of the winch allows you to easily strip it down for service and greasing.

Technical Information

Specification Details

Specification Details
Base "B" Ø (mm)318
Drum "D" Ø (mm)170
Height "H" (mm)305
J Motor Depth (mm)247
K Max Deck (mm)106
Line Entry "L" (mm)127
N Motor Length (mm)382
S Gear Length (mm)73

Resource Files


Need some advice?

Send us a

Find a