Rigging Product Roll Swaging Specifications
Correct installation of a swage fitting requires that the shank of the fitting be formed down onto the wire with specialised dies and presses in accordance with the following dimensions:
|
Wire Diameter
|
mm
|
2.5
|
3
|
4
|
5
|
5.6
|
6
|
7
|
8
|
|
in.
|
3/32
|
1/8
|
5/32
|
3/16
|
7/32
|
1/4
|
9/32
|
5/16
|
|
|
Code
|
mm
|
2.5M
|
03M
|
04M
|
05M
|
-
|
06M
|
07M
|
08M
|
|
in.
|
03
|
04
|
05
|
06
|
07
|
08
|
09
|
10
|
|
|
Length of Wire
Inside Swage |
mm
|
32.3
|
38.4
|
45
|
55
|
60.5
|
70
|
78.5
|
88
|
|
in.
|
1.27
|
1.51
|
1.77
|
2.17
|
2.38
|
2.76
|
3.09
|
3.46
|
|
|
Diameter O.D.
Before Swaging |
mm
|
5.54
|
6.35
|
7.54
|
9.12
|
10.85
|
12.55
|
14.30
|
16.13
|
|
in.
|
0.218
|
0.250
|
0.297
|
0.359
|
0.427
|
0.494
|
0.563
|
0.635
|
|
|
Diameter O.D.
After Swaging |
mm
|
4.83
|
5.56
|
6.35
|
7.95
|
9.53
|
11.13
|
12.70
|
14.30
|
|
in.
|
0.190
|
0.219
|
0.250
|
0.313
|
0.375
|
0.438
|
0.500
|
0.563
|
|
|
Tolerance on O.D.
|
mm
|
+0, -0.13
|
+0, -0.18
|
+0, -0.20
|
|||||
|
in.
|
+0, -0.005
|
+0, -0.007
|
+0, -0.008
|
||||||
|
Wire Diameter
|
mm
|
10
|
11
|
12
|
14
|
16
|
19
|
22
|
26
|
|
in.
|
3/8
|
7/16
|
1/2
|
9/16
|
5/8
|
3/4
|
7/8
|
1
|
|
|
Code
|
mm
|
10M
|
-
|
12M
|
14M
|
16M
|
19M
|
22M
|
26M
|
|
in.
|
12
|
14
|
16
|
18
|
20
|
24
|
28
|
32
|
|
|
Length of Wire
Inside Swage |
mm
|
110
|
122
|
140
|
157
|
176
|
210
|
245
|
286
|
|
in.
|
4.33
|
4.80
|
5.51
|
6.18
|
6.93
|
8.27
|
9.65
|
11.26
|
|
|
Diameter O.D.
Before Swaging |
mm
|
17.86
|
19.84
|
21.44
|
24.99
|
28.17
|
34.52
|
40.46
|
46.02
|
|
in.
|
0.703
|
0.781
|
0.844
|
0.984
|
1.109
|
1.359
|
1.593
|
1.812
|
|
|
Diameter O.D.
After Swaging |
mm
|
15.88
|
17.48
|
19.05
|
22.23
|
25.40
|
31.75
|
36.50
|
41.28
|
|
in.
|
0.625
|
0.688
|
0.750
|
0.875
|
1.000
|
1.250
|
1.437
|
1.625
|
|
|
Tolerance on O.D.
|
mm
|
+0, -0.20
|
+0, -0.23
|
+0, -0.26
|
+0, -0.31
|
||||
|
in.
|
+0, -0.008
|
+0, -0.009
|
+0, -0.010
|
+0, -0.012
|
|||||
